< Previous 1 2 3 4 5 Next >

Jim on August 11, 2019 at 9:41 AM said:

Trying to contact for purchase...
Please contact:
j_allen374@hotmail.com

chis on May 23, 2019 at 5:25 PM said:

dismantle the indexing assy I would start by sliding the top rail away from the indexing plate and spring.

Do you have a picture of the top rail?

I check all the parts and it does not show any top rail

Thank you

Christopher on April 10, 2019 at 5:49 PM said:

I have a Hobart model 110 I am looking for instructions on how to replace the grease in the gear drive.

sam on January 21, 2019 at 9:07 AM said:

I tried to email a queastion on a old A200 mixer with first gear not working and it kicked back as not valid email.

sam on January 21, 2019 at 9:07 AM said:

I tried to email a queastion on a old A200 mixer with first gear not working and it kicked back as not valid email.

John on September 5, 2018 at 3:05 PM said:

I have sent an email to oldhobartdlicer but comes back address unavailable. Anyway looking for a complete carriage assembly for a Hobart 610 slicer. Any body got any ideas?
Please email me at. Rollthediceinc@gmail.com

Ronny on July 26, 2018 at 1:22 PM said:

Have an 808 slicer that requires a replacement knife bearing unit. Need information on the removal of the old one. ranchnetex@yahoo.com

Tara on July 22, 2018 at 8:21 AM said:

I'm looking for the manual for what I believe to be a Globe 75 slicer. Do you stock these or know where I can get one.

Dan - kitchen kettle foods on February 6, 2018 at 12:31 PM said:

I have used you guys twice. excellent variety of parts and info to help with some of the challenging repairs.
Thanks

Paul Dean on October 22, 2017 at 6:45 PM said:

Is it possible to sharpen a 410 blade without factory sharpener. I have acquired a working 410 but no sharpening stones

Tom Garlick on August 27, 2017 at 1:52 PM said:

I have a globe model 75 slicer. Does anyone have a parts breakdown for this unit? I am having issues with the blade hub bearings and the center plate. When I tighten the nut for the center plate it pinches the hub bearings to the point of locking up the blade.

Tom Garlick on August 27, 2017 at 1:52 PM said:

I have a globe model 75 slicer. Does anyone have a parts breakdown for this unit? I am having issues with the blade hub bearings and the center plate. When I tighten the nut for the center plate it pinches the hub bearings to the point of locking up the blade.

Rob Green on August 13, 2017 at 10:11 AM said:

Just scored a fully eauipped 410 at a local flea market, they had me at 'Hobart'. Runs great and came with the sharpener. The only issue was the original power cord had cracked outer insulation so I ordered one from you guys. Glad I found this site.

Johnvanbrocklin@yahoo.com on December 3, 2016 at 2:22 PM said:

I just Bought a Sanitary Slicer s-4 ser-n 26264 Belvidere, Ill. work good, I like to know about how old it is and get a operator manual or repair manual and thank your help would be very much appreciated john

Bob on November 8, 2016 at 6:37 AM said:

stumbled across your site while hunting parts for our 1612. maintain kitchen equip. on two campuses of a 100 + yo boarding school. so glad to have found you!

< Previous 1 2 3 4 5 Next >